Search results for "acid etching"

Effectiveness of Preservative Treatments on Coloured Ruditic Building Stones

2009

:  The dark grey Breccia di Billiemi and the Ammonitico Rosso of Piana degli Albanesi, two coloured stones widely used in monuments both outdoor and indoor in Sicily, undergo significant decay as effect of weathering: colour change and development of surface microcracks which affect not only the chromatic aspect but also the state of aggregation. In a previous study (Fracture and Failure of Natural Building Stones, 2006, Springer, Dordrecht, The Netherlands: 329), such effects were successfully reproduced on laboratory samples by means of artificial accelerated weathering and the different response of veins and grains to the ageing agents was related to the microstructure of stones. In this…

Evaluation of accelerated weathering effects on the surface of two coloured sicilian building stones

2007

The dark grey Breccia di Billiemi and the Ammonitico Rosso of Piana degli Albanesi, widely employed outdoor and indoor in monuments in Sicily, undergo significant alteration processes, affecting not only the chromatic aspect but also the state of aggregation. In a previous paper [1] the effects of accelerated weathering in laboratory was compared with natural ageing in the urban environment. The study included the description of lithofacies, the characterisation by means of petrographic and physical-chemical techniques and accelerated weathering experiments on both lithotypes.

In vitro comparison of the retention capacity of new aesthetic brackets.

1999

Tensile bond strength and bond failure location were evaluated in vitro for two types of aesthetic brackets (non-silanated ceramic, polycarbonate) and one stainless steel bracket, using bovine teeth as the substrate and diacrylate resin as the adhesive. The results show that metallic bracket had the highest bond strength (13.21 N) followed by the new plastic bracket (12.01 N), which does not require the use of a primer. The non-silanated ceramic bracket produced the lowest bond strength (8.88 N). Bond failures occurred mainly between bracket and cement, although a small percentage occurred between the enamel-cement interface with the metal and plastic brackets and within the cement for the …

Applications of confocal laser scanning microscopy to dental bonding.

1998

The introduction of confocal laser scanning microscopy (CLSM) has provided a valuable new technique for the visualization of bonding structures such as a hybrid layer in dentin (Watson, 1989, 1991), In the case of seven commercially-available dentin bonding systems, it could be demonstrated that the CLSM renders considerably more detailed information than the SEM because of its nondestructive nature and because of the possibility of a distinction between components of bonding agents. With most of the bonding systems, measurements of the thickness of the hybrid layer could be carried out when the primer component was labeled with rhodamine B. It was found that this thickness is significantl…

How can droplet formation occur in endodontically treated teeth during bonding procedures?

2008

PURPOSE: The aim of this in vivo study was to clarify how blistering formation occurs along intraradicular dentin bonded interfaces. MATERIALS AND METHODS: Patients were selected and post space was prepared in vivo in endodontically treated teeth. Post space was etched, dried with ethanol, and bonded with one of the following adhesive systems: All Bond 2, XP-Bond, Clearfil SE Bond, Xeno III. The four adhesives were considered as representative of each bonding system class. An additional group was prepared with phosphoric acid treatment + application of Pre-Bond unfilled resin of All Bond 2, without the use of the primer agent. Etching was avoided for self-etching materials. Replicas of the …

Marginal integrity of class V restorations: SEM versus dye penetration.

2006

To perform an in vitro investigation on the marginal integrity of different adhesives (Optibond FL, Scotchbond 1XT, Clearfil SE Bond, Adper Prompt L-Pop, S(3) Bond, iBond exp., Adper Prompt L-Pop) in combination with Tetric Ceram as well as an experimental silorane-restorative (Hermes, Hermes Bond; 3M ESPE) using SEM and dye penetration (2% methylene blue) in a comparative manner.Standardized class V-cavities (3 mm x 1.5 mm) were prepared in 70 extracted human teeth (n=10). The adhesives were applied according to manufacturers' instructions. The cavities were restored with three increments. After finishing and polishing (Sof-Lex discs) and thermocycling (5000x, 5/55 degrees C), replicas wer…

Surface debris of canal walls after post space preparation in endodontically treated teeth: A scanning electron microscopic study

2004

Abstract Purpose To evaluate surface cleanliness of root canal walls along post space after endodontic treatment using 2 different irrigant regimens, obturation techniques, and post space preparation for adhesive bonding. Study design Forty teeth, divided into 4 groups, were instrumented, using Ni-Ti rotary files, irrigated with NaOCl or NaOCl + EDTA and obturated with cold lateral condensation (CLC) or warm vertical condensation (WVC) of gutta-percha. After post space preparation, etching, and washing procedure, canal walls were observed using a scanning electron microscope (SEM). Amount of debris, smear layer, sealer/gutta-percha remnants, and visibility of open tubules were rated. Result…

Effect of 2% Chlorhexidine Following Acid Etching on Microtensile Bond Strength of Resin Restorations: A Meta-Analysis.

2019

Background and Objectives: The aim of this systematic review was to examine the effect of 2% chlorhexidine following acid etching on the microtensile bond strength of resin restorations for different follow-up times. Materials and Methods: A thorough search of PubMed, Scopus, and Embase databases were conducted. In vitro experimental studies or in vivo studies published up to December 2018 with an experimental group treated with a 2% chlorhexidine solution following acid etching and a control group were included, wherein the final restoration used a resin composite in both the groups. Results: Twenty-one articles were identified for qualitative analysis and 18 for meta-analysis. The differe…

POSITIONING SELF-ETCHING ADHESIVES: VERSUS OR IN ADDITION TO PHOSPHORIC ACID ETCHING?

2004

Sealing capacity of a photochromatic flowable composite as protective base in nonvital dental bleaching.

2006

Aim  To evaluate microleakage of a flowable composite used as a protective isolating base, applied with different adhesive systems. Methodology  Seventy root-filled teeth were divided into seven groups. A flowable composite base (Tetric Flow Chroma) was used with three adhesive techniques (Syntac, Excite, Excite DCS; in the three cases with and without acid etching) and in a control group without dentine conditioning or adhesive placement. A 30% hydrogen peroxide solution was applied for 24 h in the pulp chambers, followed by the placement of a dye (silver nitrate) for 4 h. Each tooth was sectioned longitudinally, and examined under 4× magnification to assess the tooth/restoration dye leaka…